Time
Click Count
Compare angle grinder torque at the output spindle, at a stated operating speed, and under conditions that reflect the intended work. A larger torque figure alone does not establish which grinder will remove material faster or sustain a demanding cut: the figure could describe a brief peak, a calculated value, or performance at a speed unrelated to the application.
Start by matching wheel size and intended duty, then examine torque alongside output power, speed control, thermal limits, and the accessory used. When a supplier cannot identify where or how torque was measured, treat the number as incomplete rather than placing it directly beside a competitor's rating.
Torque is rotational force, expressed in newton-metres (N·m). For an angle grinder, the most useful comparison is torque available at the spindle while the wheel is working. That is different from torque measured at the motor shaft, before the reduction gears. Gear reduction changes speed and torque, and friction introduces losses, so motor-shaft and spindle figures are not interchangeable.
Ask whether the published value is continuous, peak, starting, or stall torque. Continuous torque describes a level the tool can sustain under the supplier's defined thermal and operating conditions. Peak torque is available for a limited period, but its duration and the conditions that trigger it must be stated. Starting torque relates to acceleration from rest; stall torque describes a stationary shaft under a specified condition. Neither establishes how well a grinder performs during a normal cut.
Some catalogues use an unqualified phrase such as “maximum torque.” That label does not reveal the measurement point, duration, spindle speed, or supply conditions. Request the underlying test method and a torque-speed curve, or at least a spindle torque value at a specified loaded speed and duration. If those details are unavailable, use a controlled application trial to compare performance.

At a particular operating point, mechanical output power equals torque multiplied by angular speed. When speed is expressed in revolutions per minute, the relationship is:
Output power (W) = torque (N·m) × speed (rpm) ÷ 9,550.
For example, a spindle delivering 2 N·m at 6,000 rpm produces approximately 1,257 W of mechanical output at that operating point. This is an illustration of the relationship, not a rating for any particular grinder. The calculation is valid only when torque and speed refer to the same shaft and occur at the same time.
Do not substitute a grinder's no-load speed into this equation alongside a peak or stall torque figure. No-load speed is measured with negligible working load; stall torque occurs at zero speed. Multiplying the two creates an output-power figure that the tool does not deliver at either condition.
Also distinguish electrical input power from mechanical output power. A corded tool rated in watts may show power drawn from the supply rather than power delivered to the spindle. A battery voltage and amp-hour rating describe the battery, not the grinder's continuous spindle output. Losses in the motor, electronics, and gearing prevent direct conversion without further measurements.
Two grinders can have similar no-load speeds yet behave differently under pressure. A tool with effective electronic speed control may hold speed over part of its working range, while another slows more noticeably. Once either reaches its power, current, or temperature limit, additional pressure can cause a rapid speed drop or protective shutdown.
For weld blending, a steadier speed under moderate contact can support a consistent finish. For repeated cuts through thick stock, sustained power and resistance to overheating may matter more than a short torque surge. Compare the curve near the speed and load used in the task, rather than selecting the highest point on it.
Spindle torque does not translate into the same force at every wheel diameter. At the working edge, tangential force is approximately torque divided by the effective contact radius. With the same spindle torque, a smaller effective radius produces greater tangential force. A larger wheel, however, offers different reach, cutting depth, and peripheral speed, so wheel diameter cannot be reduced to a torque advantage alone.
Wheel wear changes that radius during a job. A worn abrasive wheel has a smaller effective diameter than a new one, and its cutting behavior also changes with abrasive condition and contact geometry. Compare tools with equivalent wheel diameter, thickness, abrasive type, and wear state. For cutting-off discs, the kerf and material thickness influence the load; for grinding discs, contact area and angle affect it.
Respect the accessory's maximum permitted speed and the grinder's specified wheel size and mounting arrangement. A high-speed tool paired with an unsuitable wheel is not a valid performance comparison. Use the prescribed guard and compatible flanges for each setup; do not alter safety equipment to make two tools appear equivalent.
A useful comparison records the conditions behind each value, not just the value itself. The following fields expose the differences most likely to change the result:
For pneumatic grinders, supply conditions deserve particular attention. Pressure measured at the tool inlet under flow can differ from the pressure indicated at a regulator with the tool idle. Hose length, internal diameter, fittings, and available air flow affect the pressure reaching the tool. Compare pneumatic torque figures only when the inlet pressure and flow conditions are stated, and reproduce those conditions during a trial.
For cordless models, record the exact battery pack used in the test. Packs with the same nominal voltage do not necessarily deliver the same current under load, and state of charge or temperature can affect output and protection behavior. A result obtained with one pack should not automatically be assigned to every compatible pack.
A grinder that slows during a long pass is not necessarily deficient in peak torque. Heat buildup in the motor, electronics, battery, or gearbox can trigger reduced output or shutdown. Airflow blocked by dust accumulation, a restrictive environment, or an aggressive duty cycle can change the outcome. Conversely, a tool that feels strong for a few seconds has not demonstrated that it can sustain that load.
Ask suppliers to describe the duty cycle behind continuous ratings: the load applied, its duration, ambient conditions, and whether speed or output changes as the tool warms. A meaningful response identifies the test conditions; “heavy duty” alone is not a measurable duty rating.
Electronic features also affect observed behavior. Soft start controls acceleration, while overload protection and kickback response intervene under particular conditions. Repeated stoppages during a trial warrant investigation: an excessive feed force, a binding disc, an electrical supply issue, or a protection event can all interrupt work. Do not disable protective functions to obtain a higher result.
When torque definitions differ, compare candidate grinders on the same representative task. Select material and thickness from the intended workload, use equivalent new accessories within each tool's approved range, and prepare consistent workpieces. Record the supply arrangement, battery pack where relevant, starting temperature, wheel dimensions, and speed setting.
Keep the working technique as consistent as the task permits. For a cutting trial, compare completed cuts of the same length and geometry, while noting visible slowing, binding, and interruptions. For surface grinding, use the same material and defined work area; compare the amount removed and the resulting finish. Contact force and angle influence both outcomes, so repeat the runs and avoid treating a single fast pass as conclusive.
Observe the tools through a representative sequence of work and rest periods. Record when output falls, when protection activates, and whether the tool returns to service after cooling according to its instructions. Keep abrasive consumption separate from material removal: an aggressive wheel can shorten a cut while wearing faster, which is a property of the combined tool-and-accessory setup.
Document the result as a condition-specific comparison. A grinder that leads on a short cut may not lead during repeated work, and a setup selected for fast stock removal may leave an unsuitable finish. Retain the test conditions with the specification sheet so that a later accessory or battery change is not mistaken for a change in the tool's inherent torque.
When a torque claim is central to selection, request the measurement point, speed, test duration, supply conditions, and whether the figure is measured or calculated. Ask for the associated speed curve and the definition of continuous duty. For a pneumatic model, include tool-inlet pressure and air consumption under the stated test condition; for a cordless model, identify the pack used.
If a supplier supplies only input power and no-load speed, those values remain useful for describing the tool, but they do not determine its loaded spindle torque. Mark the torque comparison as unresolved and base the final assessment on documented application results, acceptable operating limits, and the consistency of the available evidence.
Recommended News